How to hang posters, picture frames & canvas prints?
How to hang posters?
A lot of people either don’t want to place their poster print into a frame either because their print is not a standard size, they don’t want the extra expense associated with a frame or they just prefer to hang the print on the wall as it is.
ClipsBulldog clips are available in a variety of sizes & colours and one in each top corner of the poster print which is then hung onto a small nail or screw is a great easy way & if you find that the bottom of the print is curling up then why not attach a couple more at the bottom as paper weights. You can also use crocodile or alligator clips.
Magnet ClipsMagnetic cable clips can be used in a similar way but another way is to tape something magnetic to the wall like a paper clip or a thin magnet and use something like a notice board magnet to hold the poster on the wall. If it’s a panoramic poster print then just place as many magnets along the wall as required.
VelcroSelf adhesive Velcro tape, need I say more other than make sure it wont damage your wall when removed.
Another slightly more involved way to to hang a poster without a frame is to use magnets.
- 1. Get 4 pieces of wood about 20-30mm wide & about 10mm thick, cut to the length of the top & bottom of the print. You will also need some magnets that are smaller than the bits of wood like about 10mm diameter by 2-5mm deep & a drill bit the same size as the magnet diameter.
- 2. Measure in from each end about 30mm & mark with a pencil & depending on the weight & size of the print mark one or several points in between making sure they are identical on all of the bits of wood then drill a hole deep enough so that the magnet will sit flush with the surface but not too deep as to go all the way through the wood so the use of a vice or clamp is recommended. Place all the magnets into the wood with a bit of glue to hold them in place making sure that you use the two faces that attract each other & once set take two bits & clamp the bottom of the poster between the two bits of wood.
- 3. For the top take one of the bits of wood & fit two small screw eyes & attach a piece of cord between them to hang it on then clamp the top of the poster in the same way as the bottom.
- A very neat, good looking solution but does require a little bit of DIY.
Pins or Tacks
One of the most common ways to hang posters on the wall is with the good old drawing pin or thumb tack. Quick & easy to do but can only really be done on a plasterboard or wooden wall & does leave small holes.
Blue-tac is probably the second most used method; little bit on the back of the poster in each corner, if needed along the edges, press into place, job done. If you want to replace it or move it then it only takes a few minutes.
Tape can be used on most surfaces but try to use a variety especially made for the purpose that is easy to remove without causing damage to the paint or wallpaper you are sticking it to.
Clothes HangersYes you read it right, clothes hangers or more precisely the type that you use to hang trousers or skirts, the ones with clamps either at each end of the hanger or my preferred favourite the older style wooden variety that clamps together. Again depending on the size of the posterprint you can use one, two or more.
Any Ideas?I’m sure there are many more ways of hanging your posterprints & if you have one that you would like to share then please email us & we will add it to the list.
We hope this answers your questions about how to hang a posters. Meanwhile...
How to hang picture frames?Normally the first thing people ask when they receive their parcel from Posterprint is; How to hang picture frames? When you receive your framed picture from Posterprint.co it will come ready to hang with either low stretch picture cord or on larger frames hanging plates.
WarningBefore making a hole in any type of wall look down at the bottom of the wall to make sure that there are no electrical sockets below & up to make sure there are no light fittings on the wall. If there are then the electrical wires for them may come directly up or down the wall. If you are unsure then either move the location of the fixing or purchase a wall scanner that is able to detect electrical cables behind the surface.
TipA lot of people make the mistake of drilling the correct size hole & then hammering the raw plug in so that only half goes in before it deforms with the hammer blow then they remove the plug & drill a bigger hole which is then too big and leads to a weak fixing. The way to do it is drill the hole & gently tap the plug in as far as it will go then get your screw, place it in the plug & tap the screw which will in turn push the plug into the wall for a nice tight fixing. I generally prefer to use a red raw plug with a drill size of 6mm for a very hard wall or 5.5mm for softer versions.
Picture frame hooks with hardened nailsThese can be purchased with either one, two or three nails and can be used on plasterboard walls for smaller, lighter frames or plastered masonry block but can be difficult to hammer in without causing plaster to chip off or nails to break.
Stud wall with plasterboardIf you have a stud finder then use that or if you have a good ear you can go along the wall tapping the plasterboard and listen for a change in tone which will normally indicates a stud at that location. If you are lucky enough to have a stud then it’s a simple case of either carefully hammering in a suitable nail or use a suitable size screw at the required height. If no stud is available, for smaller framed posters then a simple raw plug & screw is more than sufficient. Make a hole in a downward direction in the plasterboard with either a drill or even a small screwdriver that is slightly smaller than the raw lug. Tap the raw plug gently into the hole & screw in the screw. For larger frames then a metal self drive plasterboard fixing with self tapping screw will be ideal but don’t bother with the plastic versions.
Plastered masonry blockThe easiest wall when it comes to how to hang picture frames. My preferred method is the good old raw plug & screw.
Stone wallIf your stone wall isn’t rendered then find a suitable size stone to drill a hole into & use a raw plug & screw. If it is rendered then it can be a little bit of trial & error finding a stone & not a joint. If you do drill into a joint then that would generally not be good enough for a fixing.
We hope this answers your questions about how to hang picture frames. And yet again... Happy hanging!